Smart home devices are always on — always listening, always connected. Homeowners in Toronto and the GTA worry that dozens of always-on devices are quietly running up their electric bill. The reality is much smaller than most people expect, but not zero. This guide breaks down the real electricity use of common smart home devices and where the actual power savings and costs land.
Do smart home devices use a lot of electricity?
Individually, smart home devices use very little electricity. A smart plug draws 0.5–2 watts in standby. A smart bulb draws 0.3–0.6W in standby (much less than the 60W or so when on). A smart speaker like Amazon Echo draws 2–3W idle. A hub draws 1–5W. Even a home with 50+ smart devices adds maybe $30–$80 CAD per year to the electric bill in Ontario. That is offset many times over by smart-lighting savings, smart-thermostat HVAC savings, and load-scheduling on time-of-use rates.
Standby draw of common smart devices
Smart plug (Wi-Fi): 0.5–2W standby.
Smart plug (Zigbee/Z-Wave): 0.3–1W standby.
Smart bulb (idle): 0.3–0.6W.
Smart switch: 0.3–1W.
Amazon Echo Dot: 1.5–2.5W idle.
Google Nest Hub: 2–4W idle.
Wi-Fi router: 5–12W (existing regardless).
Zigbee/Thread hub: 2–5W.
Smart thermostat: 1–2W.
Smart doorbell (wired): 3–6W.
Smart security camera (Wi-Fi): 3–10W each.
Actual annual cost math
Sample GTA home with 50 smart devices averaging 1.5W standby draw each:
50 devices × 1.5W = 75W continuous.
75W × 24 hours × 365 days = 657 kWh/year.
At Ontario average ~$0.11–$0.15 per kWh = ~$70–$100 CAD/year total for all standby.
Compare to a single always-on 60W incandescent bulb, which is 526 kWh/year for one bulb.
Where smart devices save electricity
Smart thermostats. Schedule-based heating/cooling saves 8–15% on HVAC bills.
Smart lighting. Automatically off in unoccupied rooms, dimmed in evenings, LED efficiency gains.
Smart plugs for phantom loads. Kill standby power to TVs, sound systems, and computers when not in use.
Time-of-use scheduling. Run high-load appliances (dishwasher, EV charger) during Ontario off-peak hours.
Automated blinds. Control sun exposure for passive heating/cooling savings.
For a typical GTA home, smart-thermostat savings alone can exceed the cost of running all standby smart devices combined.
Watch out for these power hogs
Old-generation Wi-Fi cameras. Can draw 10W+ each; five cameras = $50–$60/year.
Wi-Fi hubs that duplicate router functions. Unnecessary bridges add draw.
Smart displays with always-on screens. Dim them or set them to sleep.
Cheap smart plugs. Some no-name brands draw 3–5W idle vs 1W for major brands.
Legacy smart-home computers or servers. Home Assistant on a full desktop can draw 40–80W. Use a Raspberry Pi or mini PC instead.
Actual electricity savings you can measure
Ontario smart-home users typically see:
$150–$300/year HVAC savings from smart thermostats.
$50–$100/year lighting savings from LEDs + smart control.
$50–$100/year from killed phantom loads.
$100–$300/year from EV time-of-use scheduling.
Net effect for most GTA smart homes: modest savings that offset standby draw and then some.
Best practices to minimize smart-home standby draw
Prefer Zigbee, Z-Wave, Thread, or wired ethernet over Wi-Fi where possible.
Consolidate hubs rather than one bridge per brand.
Buy CSA/cULus-certified major brands (better standby efficiency).
Set smart displays and speakers to sleep at night.
Use smart plugs to kill entertainment centre phantom loads when not watching TV.
Expert tip from our ESA-licensed electricians
Do not obsess about the 1W standby draw of a smart bulb. In an average GTA home, the biggest electricity hogs are still the fridge, HVAC, water heater, and dryer — not the smart devices. If you are optimizing energy use, spend your attention on the smart thermostat schedule, LED upgrades, and killing phantom loads on entertainment gear. The 50 smart plugs sipping half a watt each are noise in the signal.
Frequently Asked Questions
Do smart bulbs use power when off?
Yes, minimal — typically 0.3–0.6W per bulb for the radio and standby circuit.
Are Wi-Fi cameras big electricity users?
Older cameras yes (10W+). Modern efficient models draw 3–5W.
Does a smart thermostat pay for itself?
Usually within 1–2 heating/cooling seasons through automated scheduling savings.
Planning a smart-home retrofit in a Toronto or GTA home and want the electrical done right? Call ezsmart at 416-838-9006 or use our contact page. An ESA-licensed electrician can pre-wire, add neutrals, and support your smart-home vision.
Used to monitor number of Google Analytics server requests
10 minutes
__utmb
Used to distinguish new sessions and visits. This cookie is set when the GA.js javascript library is loaded and there is no existing __utmb cookie. The cookie is updated every time data is sent to the Google Analytics server.
30 minutes after last activity
__utmc
Used only with old Urchin versions of Google Analytics and not with GA.js. Was used to distinguish between new sessions and visits at the end of a session.
End of session (browser)
__utmz
Contains information about the traffic source or campaign that directed user to the website. The cookie is set when the GA.js javascript is loaded and updated when data is sent to the Google Anaytics server
6 months after last activity
__utmv
Contains custom information set by the web developer via the _setCustomVar method in Google Analytics. This cookie is updated every time new data is sent to the Google Analytics server.
2 years after last activity
__utmx
Used to determine whether a user is included in an A / B or Multivariate test.
18 months
_ga
ID used to identify users
2 years
_gali
Used by Google Analytics to determine which links on a page are being clicked
30 seconds
_ga_
ID used to identify users
2 years
_gid
ID used to identify users for 24 hours after last activity
24 hours
_gat
Used to monitor number of Google Analytics server requests when using Google Tag Manager
1 minute
_gac_
Contains information related to marketing campaigns of the user. These are shared with Google AdWords / Google Ads when the Google Ads and Google Analytics accounts are linked together.
90 days
SourceBuster is used by WooCommerce for order attribution based on user source.
Name
Description
Duration
sbjs_session
The number of page views in this session and the current page path
30 minutes
sbjs_udata
Information about the visitor’s user agent, such as IP, the browser, and the device type
session
sbjs_first
Traffic origin information for the visitor’s first visit to your store (only applicable if the visitor returns before the session expires)
session
sbjs_current
Traffic origin information for the visitor’s current visit to your store
session
sbjs_first_add
Timestamp, referring URL, and entry page for your visitor’s first visit to your store (only applicable if the visitor returns before the session expires)
session
sbjs_current_add
Timestamp, referring URL, and entry page for your visitor’s current visit to your store
session
sbjs_migrations
Technical data to help with migrations between different versions of the tracking feature
session
Marketing cookies are used to follow visitors to websites. The intention is to show ads that are relevant and engaging to the individual user.
Google Maps is a web mapping service providing satellite imagery, real-time navigation, and location-based information.
